 |
 |
Online Catalog
Type S Bushing Dies
 |
The amount of resizing provided by conventional reloading dies has always been dictated by the manufacturing tolerances (SAAMI specifications) of the brass cartridge case itself. Reloading die manufacturers have been forced to design the neck diameter of their dies small enough to accommodate the thinnest possible brass. This may be as much as .008" - .010" smaller than the maximum cartridge dimensions typically shown in most reloading manuals. Since the majority of cases that the reloader is likely to encounter in the field are thicker than the minimum specifications that the dies were designed for, case necks are often resized excessively. It can be easily demonstrated that excessive resizing of the cartridge case quickly leads to stress distortion and concentricity problems. The new Type S - Bushing Style Dies offer a simple solution to this age old problem. |
The Type S - Bushing Style Dies, Competition Seating and Neck Sizing Dies, Body Dies and our New Competition Shellholders are all products of Benchrest and 1000 yard Competition.
Type S – "Elite" Bushing Die Set
INCLUDES –•Type S – Bushing Full Sizing Die
•Type S – Bushing Neck Sizing Die
•Competition Seating Die
Redding Reloading Equipment has once again established a new die set based on customer feedback. The past few years you have seen the introduction of many new sets like the National Match, Master Hunter and the Premiums as a result of changing trends in the category and stated desires of the customer base. The latest, the Redding, Type S Elite die set is also a direct result of customer feedback and is available for 85 different cartridges.
The Type S Elite set is comprised of a Type S Bushing Full Die, A Type S Bushing Neck Die and the unparalleled Redding Competition Seating Die. All Type-S dies use an interchangeable bushing to control neck diameter and tension to an increment of 0.001”. Bushings are available in hardened steel but also are available with a TIN (Titanium Nitride) coating for even greater lubricity. This allows the handloader complete control and precision when setting the appropriate neck tension without fear of over working the brass in the case neck. These bushings are also free-floating to self- center on the case neck for a higher degree of sizing accuracy. These features provide not only an enhanced degree of control but significant improvements to consistency and accuracy of the final loaded rounds.
Type S – Neck Bushing Die
The Type S - Bushing Style Dies, Competition Seating and Neck Sizing Dies, Body Dies and our New Competition Shellholders are all products of Benchrest and 1000 yard Competition.The Type S - Bushing Style Neck Sizing Die provides reloaders with a simple means to precisely control case neck size and tension.
- Uses interchangeable sizing bushings available in .001" increments.
- The adjustable decapping rod allows positioning the bushing to resize only a portion of the neck length if desired.
- Concentricity is enhanced by the ability of the resizing bushing to selfcenter
- on the case neck.
- The decapping rod is supplied with a standard size button. This is especially useful for reloaders who are using commercial brass as is.
- A decapping pin retainer is also supplied with most Type S - Bushing Dies except 17 and 20 Cal. This enables neck sizing without the use of the size button for those who sort and/or turn case necks for uniformity.
Type S Die Charts by Caliber Click Here
Category I . . . . . . . . . . . . . . . . .
Category II . . . . . . . . . . . . . . . .
Category III . . . . . . . . . . . . . .
Carbide size button kits are also available for all Type S Dies. Click Here for kit numbers by caliber.
Type S – Full Bushing Die
Full length resizing while maintaining exact control of the case neck is often desirable in one operation. The new Type S - Full Length Resizing/Bushing Die accomplishes this task with the precision you would expect from Redding.- Uses the same interchangeable bushings (.001" increments) as those used in our bushing style neck sizing dies.
- The adjustable decapping rod allows you to adjust the bushing position, sizing only part of the neck length when desire d .
- Concentricity is enhanced by the ability of the bushing to self-center on the neck of the cartridge case.
- All Type S (except 17 and 20 Cal.) dies are supplied with both the standard size button and a decapping pin retainer for the advantages and versatility described under our Type S - Bushing Style Neck Sizing Dies.
All dies are supplied without bushings.
Type S Die Charts by Caliber Click Here
Category I . . . . . . . . . . . . . . . . .
Category II . . . . . . . . . . . . . . . .
Category III . . . . . . . . . . . . . .
